|
UV LED Offset Printing Ink FAST DRY High Color Intensity PET PVC
| MOQ: | 1 |
| Price: | SG$3.78-4.95 |
LED Offset Printing Ink
,Offset Printing Ink FAST DRY
,Offset Printing Ink PET
FASTDRY UV LED ink for offset printing curing instantly under UV light.
Weatherresistant and UVproof formulation ensures longlasting print durability outdoors.
Ideal for highsheet cardboard PET film and other demanding substrates.
Soybased lowodor ink delivers high concentration pigment with ecofriendly performance.
Combines exceptional adhesion scratch resistance and consistent color fidelity on diverse surfaces.
UV-LED OFFSET SERIES INK
Energy-efficient LED-UV offset ink with instant cure and low heat exposure
| Document: TDS-UV-LED-EN | Revision: 01 | Issue date: 01 Aug 2026 |
| Product type: Energy-curable offset printing ink | Status: Typical technical data | Brand: FORDIA |
FORDIA UV-LED is formulated for offset presses equipped with LED-UV curing. The series is optimized for rapid polymerization under common LED wavelengths, supporting immediate handling, low heat input and stable printing on paper, board and approved non-absorbent substrates.
Recommended applications: Commercial printing, folding cartons, labels, books and promotional materials produced on LED-UV offset presses. Synthetic paper and films must be approved by adhesion and cure trials before production.
Recommended substrates: Coated/uncoated paper, paperboard, selected synthetic paper and pretreated film (trial required)
Recommended equipment: Sheet-fed or suitable web offset presses fitted with 385/395/405 nm LED-UV curing
Available colors: Process Yellow, Process Magenta, Process Cyan, Process Black; spot colors available on request
- Responsive curing under 385, 395 and 405 nm LED-UV systems.
- Instant dry surface for rapid turning, backing-up and downstream handling.
- Low heat load compared with conventional mercury UV, helping protect heat-sensitive substrates.
- Good dot definition, transfer, gloss and rub resistance after full cure.
- Low VOC formulation; no spray powder is normally required when cure is complete.
| Data status: Values below are typical production values, not release specifications or contractual limits. |
| Property | Typical value | Test / condition |
|---|---|---|
| Appearance | Smooth paste ink | Visual |
| Fineness | ≤ 5 µm | Grind gauge |
| Tack | 11-15 | Inkometer, 32°C, 400 rpm, 1 min |
| Viscosity | 80-130 Pa·s | Cone/plate or equivalent, 25°C |
| LED wavelength | 385/395/405 nm | Lamp output must overlap ink response |
| Typical cure dose | 40-120 mJ/cm² | At the ink surface; verify on press |
| Shelf life | 12 months | Unopened original container, recommended storage |
| Process color | Typical solid density* | Lightfastness (Blue Wool)* |
|---|---|---|
| Yellow | 1.15-1.30 | 3-5 |
| Magenta | 1.35-1.50 | 4-5 |
| Cyan | 1.45-1.60 | 7-8 |
| Black | 1.60-1.80 | 7-8 |
*Density: coated stock, Status T measurement. Lightfastness is pigment/shade dependent and indicative only.
| Control point | Recommended starting guidance |
|---|---|
| Lamp match | Confirm peak wavelength, irradiance and dose with the LED system supplier and a calibrated radiometer. |
| Ink film | Avoid excessive ink film; heavy coverage may require a higher dose, additional lamp power or lower speed. |
| Dampening | Run minimum stable water and avoid contamination with conventional oil-based ink or wash residues. |
| Cure check | Check surface and through-cure using rub, scratch, tape and odor assessment before finishing. |
| Series-specific note: Cure response depends on lamp wavelength, irradiance, accumulated dose, ink film, color, substrate and press speed. Black, opaque and heavy-coverage areas normally require the most demanding cure setting. | |
- Condition ink to approximately 20-25°C before use and mix gently until uniform.
- Keep containers closed when not in use and protect ink from sunlight, UV lamps and strong white light.
- Do not mix with conventional oil-based ink or unapproved additives. Use only FORDIA-recommended reducers or auxiliaries.
- Keep rollers, blankets, plates and ink ducts clean. Residual wash or incompatible ink can impair cure and adhesion.
- Approve color, cure, adhesion, rub resistance and finishing performance on the actual press and substrate before a production run.
Use a wash approved for UV-curable offset inks and compatible with the press rollers, blankets and plate system. Follow the press manufacturer's procedure. Prevent wash and ink residues from entering drains or surface water.
- Standard packing: 1 kg vacuum can; other pack sizes may be available by agreement.
- Store in the unopened original container at 5-25°C in a cool, dry, well-ventilated area.
- Protect from heat, freezing, sunlight and all UV radiation. Rotate stock on a first-in, first-out basis.
- Shelf life applies only under the stated storage conditions. Resealed or contaminated ink should be evaluated before reuse.
Guangzhou Fordia New Materials Technology Co., Ltd. specializes in high-performance printing consumables, offering offset, UV printing solutions and supplying offset printing machine parts. With a focus on quality and cost-effectiveness, the company serves global printing houses, providing stable products and customized solutions. It exports to Southeast Asia, the Middle East, and South America, emphasizing long-term partnerships and flexible MOQ.
Company Details
